Passively Q-Switched Er-Doped Fiber Laser Based on Bentonite Clay (Al2H2O6Si) Saturable Absorber.

This paper presents the investigations toward the direct use of bentonite clay (Al2H2O6Si) nanoparticles to act like a saturable absorber (SA) for the Q-switched pulse operation of an erbium-doped fiber laser (EDFL). The measured results reveal that with the incorporation of bentonite clay nanopowder as a SA, an EDFL is realized with a Q-switching mechanism starting at a pump power of 30.8 mW, and a Q-switched emission wavelength was noticed at 1562.94 nm at 142 mW pump power. With an increased pump from 30.8 mW to 278.96 mW, the temporal pulse parameters including minimum pulse duration and maximum pulse repetition rates were reported as 2.6 µs and 103.6 kHz, respectively. The highest peak power, signal-to-noise ratio, output power and pulse energy were noticed to be 16.56 mW, 51 dB, 4.6 mW, and 47 nJ, respectively, at a highest pump power of 278.96 mW. This study highlights the significance of bentonite clay (Al2H2O6Si) nanoparticles as a potential candidate for a saturable absorber for achieving nonlinear photonics applications.

Q-switched pulse operation in erbium-doped fiber laser subject to zirconia (ZrO2) nanoparticles-based saturable absorber.

In this paper, the zirconia (ZrO2) nanoparticles-based saturable-absorber (SA) have been incorporated in an erbium-doped fiber laser (EDFL) cavity for achieving a Q-switched pulse operation. The implementation of the zirconia nanoparticles-based powder on the fiber facet was accomplished using the index-matching gel's adhesion effect. The incorporation of SA in the laser cavity yielded a stable and self-starting Q-switched operation under 19.36 mW pump power that corresponded to the emission wavelength of 1557.29 nm. Additionally, it was observed that the EDFL's emission wavelength tuned from 1557.29 nm to 1562.3 nm , and the repetition rates and pulse width ranged from 61.2 to 130 kHz and 7.9 to 3.6 µs, respectively, as the pump power was increased from 19.36 to 380.16 mW. Measured experimental results reveal that at a maximum pump power of 380.16 mW, the maximum average output power, peak power, and pulse energy were noticed to be 1.17 mW, 2.5 mW, and 9 nJ, respectively. A 52 dB suppression in side bands was found at a pump power of 380.16 mW. Moreover, the stability and threshold tolerance of the EDFL has also been discussed in detail. These findings suggest that nanoparticle-based saturable absorbers have potential applications in a pulsed source, making it easier to implement in fiber cavity-based systems.

CF-LIBS based elemental analysis of Saussurea simpsoniana medicinal plant: a study on roots, seeds, and leaves.

The plant Saussurea Simpsoniana, which has been used in traditional medicine for its biocompatibility and abundant nutrients, offers a wide range of remedies. Local communities effectively utilize medicines derived from the plant's roots to treat various ailments such as bronchitis, rheumatic pain, and abdominal and nervous disorders. In this study, we present an elemental analysis of the chemical composition (wt%) of this medicinal plant using the laser-induced breakdown spectroscopy (LIBS) technique. In the air atmosphere, an Nd:YAG (Q-switched) laser operating at a wavelength of 532 nm is utilized to create plasma on the sample's surface. This laser has a maximum pulse energy of approximately 400 mJ and a pulse duration of 5 ns. A set of six miniature spectrometers, covering the wavelength range of 220-970 nm, was utilized to capture and record the optical emissions emitted by the plasma. The qualitative analysis of LIBS revealed the presence of 13 major and minor elements, including Al, Ba, C, Ca, Fe, H, K, Li, Mg, Na, Si, Sr, and Ti. Quantitative analysis was performed using calibration-free laser-induced breakdown spectroscopy (CF-LIBS), ensuring local thermodynamical equilibrium (LTE) and optically thin plasma condition by considering plasma excitation temperature and electron number density. In addition, a comparison was made between the results obtained from CF-LIBS and those acquired through energy-dispersive X-ray spectroscopy (EDX) analysis.

Multi-Spectroscopic Characterization of MgO/Nylon (6/6) Polymer: Evaluating the Potential of LIBS and Statistical Methods.

The potential of using laser-induced breakdown spectroscopy (LIBS) in combination with various other spectroscopic and statistical methods was assessed for characterizing pure and MgO-doped nylon (6/6) organic polymer samples. The pure samples, obtained through a polycondensation chemical technique, were artificially doped with MgO prior to analysis for comparative purposes. These artificially doped samples served as crucial reference materials for comparative analysis and reference purposes. The LIBS studies were performed under local thermodynamic equilibrium (LTE) and optically thin plasma conditions. To assess the structural crystallinity of the nylon (6/6) polymer samples, X-ray diffraction (XRD) analysis, and Fourier transform infrared (FTIR) spectroscopy were employed to detect functional groups such as N-H, C-H, and C-N in the adsorbent polyamide nylon sample. Additionally, diffuse reflectance spectroscopy (DRS) analysis was conducted to investigate the effects of doping and temperature on the band gap and material reflectance across different sample temperatures. Chemical compositional analysis was performed using X-ray photoelectron spectroscopy (XPS) with the carbon C1s peak at 248.8 eV serving as a reference for spectrum calibration, along with energy-dispersive X-ray (EDX) analysis, which demonstrated good agreement between the techniques. To validate the different methodologies, the results obtained from CF-LIBS and EDX were compared with those from the standard inductively coupled plasma mass spectrometry (ICP-MS) technique. Finally, for classification analysis, principal component analysis (PCA) was applied to the LIBS spectral data at different sample temperatures (25 °C, 125 °C, 225 °C, and 325 °C). The analyses demonstrated that the combination of LIBS with PCA, along with other methods, presents a robust technique for polymer characterization.

LIBS assisted PCA analysis of multiple rare-earth elements (La, Ce, Nd, Sm, and Yb) in phosphorite deposits.

In the present study, the immediate detection of rare-earth elements (REEs) in phosphorite deposits has been reported using laser-induced breakdown spectroscopy (LIBS). Numerous emission lines corresponding to the REEs such as lanthanum (La), cerium (Ce), neodymium (Nd), samarium (Sm), and ytterbium (Yb), have been detected in the emission spectra of phosphorite-induced plasma plume. For the quantitative analysis, we employed the calibration-free LIBS (CF-LIBS), and Energy Dispersive X-ray (EDX) spectroscopy techniques. The results obtained using the CF-LIBS technique show excellent agreement with that obtained by EDX. Besides principal component analysis (PCA) was employed by incorporating the LIBS spectral data of rare earth phosphorite rocks samples containing La, Ce, Nd, Sm, and Yb emission lines. The first three PCs were observed using LIBS spectral data set showing a covariance (interpretation rate) up to 76.3%. This study suggests that LIBS yields a quick and very reliable qualitative and quantitative analysis of REEs in any geological ore sample.

Ameliorating the stability of erbium-doped fiber laser using saturable absorber fabricated by the pulsed laser deposition technique.

In this paper, we present the performance and stability of an erbium-doped fiber laser (EDFL) based on ZnO saturable-absorber (SA) prepared using two schemes: solution method (SM) and pulsed laser deposition technique (PLDT). It was observed that EDFL with ZnO-SA prepared using SM emits at 1561.25 nm under a pump power of 230 mW. As the pump power is increased from 22.2 mW to 75.3 mW, the pulse duration decreases from 24.91 to 10.69 µs, and the pulse repetition rates increase from 11.59 to 40.91 kHz. Besides at pump power of 75.3 mW, the peak power, pulse energy, and average output power are measured as 0.327 mW, 2.86 nJ, and 0.18 mW, respectively. However, when PLDT-based SA was incorporated into the ring cavity, the emission wavelength is noticed at 1568.21 nm at a pump power of 230 mW. With the increase in pump power from 22.2 mW to 418 mW, the pulse repetition rates increase from 10.79 to 79.37 kHz and the pulse width decreases from 23.58 to 5.6 µs. Furthermore, the peak power, pulse energy, and average output power are observed to be 10.9 mW, 74 nJ, and 5.35 mW, respectively. The stability of EDFL based on SAs prepared using SM and PLDT has also been investigated. To the best of the author's knowledge, it is the first comparison of performance and long-term stability of EDFL based on two experimental techniques SM and PLDT-based SAs. These findings suggest that PLDT-based SAs provides optimum stability over a long period and enhanced the performance of fiber lasers compared to the SAs prepared using the conventional SM technique. This study paves the way for the development of ultra-stable SAs for their potential applications in pulsed laser sources and photonic devices.

Vibrational Emission Study of the CN and C2 in Nylon and ZnO/Nylon Polymer Using Laser-Induced Breakdown Spectroscopy (LIBS).

The laser-induced breakdown spectroscopy (LIBS) technique was performed on polymers to study the neutral and ionic emission lines along with the CN violet system (B2Σ+ to X2Σ+) and the C2 Swan system (d3 Пg-a3 Пu). For the laser-based emission analyses, the plasma was produced by focusing the laser beam of a Q-switched Nd: YAG laser (2ω) at an optical wavelength of 532 nm, 5 ns pulse width, and a repetition frequency of 10 Hz. The integration time of the detection system was fixed at 1-10 ms while the target sample was positioned in air ambiance. Two organic polymers were investigated in this work: nylon and nylon doped with ZnO. The molecular optical emission study of nylon and doped nylon polymer sample reveals CN and C2 molecular structures present in the polymer. The vibrational emission analysis of CN and C2 bands gives information about the molecular structure of polymers and dynamics influencing the excitation structures of the molecules. Besides, it was further investigated that the intensity of the molecular optical emission structure strongly depends on the electron number density (cm-3), excitation temperature (eV), and laser irradiance (W/cm2). These results suggest that LIBS is a reliable diagnostic technique for the study of polymers regarding their molecular structure, identification, and compositional analysis.

Laser Spectroscopic Characterization for the Rapid Detection of Nutrients along with CN Molecular Emission Band in Plant-Biochar.

We report a quantitative analysis of various plant-biochar samples (S1, S2 and S3) by utilizing a laser-induced breakdown spectroscopy (LIBS) technique. For LIBS analysis, laser-induced microplasma was generated on the target surface by using a focused beam through a high-power Nd: YAG laser and optical emission spectra were recorded using a charged coupled device (CCD) array spectrometer, with wavelength ranges from 200 nm to 720 nm. The spectroscopical analysis showed the existence of various ingredients, including H, Li, Ca, Na, Al, Zn, Mg, Sr, Si, and Fe, along with a CN molecular emission band due to B2Σ+ - X2Σ+ electronic transition. By assuming conditions of the plasma is optically thin and in LTE, calibration-free laser-induced breakdown spectroscopy (CF-LIBS) was utilized for the compositional analysis of the ingredients present in the three plant-biochar samples. To lower the uncertainties, we used an average composition (%) of the three plant-biochar samples. The quantitative study of the plant-biochar samples was also achieved using the energy dispersive X-ray (EDX) technique, showing good agreement with the CF-LIBS technique. In addition, statistical analysis, such as principal component analysis (PCA), was performed for the clustering and classification of the three plant-biochar samples. The first three PCs explained an overall ~91% of the variation in LIBS spectral data, including PC1 (58.71%), PC2 (20.9%), and PC3 (11.4%). These findings suggest that LIBS is a robust tool for rapid measurement of heavy as well as light elements, such as H, Li, and nutritional metals in plant-biochar samples.

Quantification of Aluminum Gallium Arsenide (AlGaAs) Wafer Plasma Using Calibration-Free Laser-Induced Breakdown Spectroscopy (CF-LIBS).

In this work, we report the results of the compositional analysis of an aluminum gallium arsenide (AlGaAs) sample using the calibration-free laser-induced breakdown spectroscopy (CF-LIBS) technique. The AlGaAs sample was doped with three various concentrations of gallium (Ga), arsenic (As), and aluminum (Al), as reported by the manufacturer, and the CF-LIBS technique was employed to identify the doping concentration. A pulsed Q-switched Nd: YAG laser capable of delivering 200 and 400 mJ energy at 532 and 1064 nm, respectively, was focused on the target sample for ablation, and the resulting emission spectra were captured using a LIBS 2000+ spectrometer covering the spectral range from 200 to 720 nm. The emission spectra of the AlGaAs sample yielded spectral lines of Ga, As, and Al. These lines were further used to calculate the plasma parameters, including electron temperature and electron number density. The Boltzmann plot method was used to calculate the electron temperature, and the average electron temperature was found to be 5744 ± 500 K. Furthermore, the electron number density was calculated from the Stark-broadened line profile method, and the average number density was calculated to be 6.5 × 1017 cm-3. It is further observed that the plasma parameters including electron temperature and electron number density have an increasing trend with laser irradiance and a decreasing trend along the plume length up to 2 mm. Finally, the elemental concentrations in terms of weight percentage using the CF-LIBS method were calculated to be Ga: 94%, Al: 4.77% and As: 1.23% for sample-1; Ga: 95.63%, Al: 1.15% and As: 3.22% for sample-2; and Ga: 97.32%, Al: 0.69% and As: 1.99% for sample-3. The certified concentrations were Ga: 95%, Al: 3% and As: 2% for sample-1; Ga: 96.05%, Al: 1% and As: 2.95% for sample-2; and Ga: 97.32%, Al: 0.69% and As: 1.99% for sample-3. The concentrations measured by CF-LIBS showed good agreement with the certified values reported by the manufacturer. These findings suggest that the CF-LIBS technique opens up an avenue for the industrial application of LIBS, where quantitative/qualitative analysis of the material is highly desirable.

China's Pathway towards Solar Energy Utilization: Transition to a Low-Carbon Economy.

Rapid economic growth has caused many environmental problems in China, resulting in international pressure on China to fight against climate change and to shift to a more environmentally friendly economy. Therefore, over the past decades, China has been working on transforming its economy to counter the concerns of different environmental hazards caused by the burning fossil fuels and rising oil imports to support the energy sector. This study explores the shift in the Chinese government's policies towards a low-carbon economy by adopting more environmentally friendly solar energy. A cost-benefit analysis of the solar water heater industry in China indicates that it not only brings economic benefits to society but also environmental benefits to the earth. Furthermore, this paper focuses on the use of solar energy as a kind of renewable energy, as solar energy is plentiful, which is beneficial from both an environmental and economic perspective.

Measurements of experimental transition probabilities of 3p54p → 3p54s arrays in neutral argon.

We have determined the absolute transition probabilities of 27 emission lines of neutral argon originating from the 3p54p→3p54s transition array in the wavelength region from 650 to 1100 nm using an argon-filled hollow cathode discharge lamp. The absolute transition probabilities have been deduced using the lifetimes of the upper levels and the measured branching fractions. Atomic oscillator strengths and relative line strengths for all the transitions have been computed using calculated transition probabilities. The experimentally determined transition probabilities are found to be in good agreement with that calculated in the intermediate coupling (IC) scheme. The comparison of experimentally determined transition probabilities with reported theoretical transition probabilities confirms that the IC scheme for the lower as well as for the upper levels seems to be a useful scheme for the level designation for the 3p54p to 3p54s configuration-based levels in argon. Furthermore, the measured relative line strengths are used to validate the J-file sum rule for the 3p54p→3p54s transition array of argon. The reported transition probabilities, oscillator strengths, and relative line strengths are compared with the published data, showing good agreement.

Stabilization of self-mode-locked QDash lasers subject to simultaneous continuous-wave optical injection and optical feedback.

In this paper, we report stabilization of self-mode-locked two-section quantum-dash lasers on the widest range of delay using simultaneous optical injection and optical feedback. With continuous-wave optical injection, various wavelengths spanning a range from 1568 to 1578 nm were investigated and optimum wavelengths (1571.210 to 1572.710) yielding the narrowest RF linewidth and reduced timing jitter of slave laser were identified. In addition, the dependence of RF linewidth and pulse repetition rate on injected wavelength was further explored. Our results indicate that simultaneous optical feedback and optical injection significantly improves the RF linewidth across the widest delay range compared to optical feedback alone. Under fully resonant feedback and optimum injection parameters, a minimum RF linewidth of 1 kHz (instrument limited) was achieved with simultaneous optical injection plus optical feedback, which was >2× lower than optical feedback alone and more than 100× lower than free-running. This stabilization technique is implemented in an all-optical arrangement without optical/electrical conversion, which is ideal for high-repetition-rate devices and photonic integration.

Stabilization of self-mode-locked quantum dash lasers by symmetric dual-loop optical feedback.

We report experimental studies of the influence of symmetric dual-loop optical feedback on the RF linewidth and timing jitter of self-mode-locked two-section quantum dash lasers emitting at 1550 nm. Various feedback schemes were investigated and optimum levels determined for narrowest RF linewidth and low timing jitter, for single-loop and symmetric dual-loop feedback. Two symmetric dual-loop configurations, with balanced and unbalanced feedback ratios, were studied. We demonstrate that unbalanced symmetric dual loop feedback, with the inner cavity resonant and fine delay tuning of the outer loop, gives the narrowest RF linewidth and reduced timing jitter over a wide range of delay, unlike single and balanced symmetric dual-loop configurations. This configuration with feedback lengths of 80 and 140 m narrows the RF linewidth by ∼ 4-67x and ∼ 10-100x, respectively, across the widest delay range, compared to free-running. For symmetric dual-loop feedback, the influence of different power split ratios through the feedback loops was determined. Our results show that symmetric dual-loop feedback is markedly more effective than single-loop feedback in reducing RF linewidth and timing jitter, and is much less sensitive to delay phase, making this technique ideal for applications where robustness and alignment tolerance are essential.

Asymmetric dual-loop feedback to suppress spurious tones and reduce timing jitter in self-mode-locked quantum-dash lasers emitting at 1.55 µm.

We demonstrate an asymmetric dual-loop feedback method to suppress external cavity side-modes induced in self-mode-locked quantum-dash lasers with conventional single- and dual-loop feedback. In this Letter, we report optimal suppression of spurious tones by optimizing the delay in the second loop. We observed that asymmetric dual-loop feedback, with large (∼8×) disparity in loop lengths, gives significant suppression in external-cavity side-modes and produces flat radio frequency (RF) spectra close to the main peak with a low timing jitter, compared to single-loop feedback. Significant reduction in RF linewidth and timing jitter was produced by optimizing the delay time in the second feedback loop. Experimental results based on this feedback configuration validate predictions of recently published numerical simulations. This asymmetric dual-loop feedback scheme provides simple, efficient, and cost-effective stabilization of optoelectronic oscillators based on mode-locked lasers.

Optimum stabilization of self-mode-locked quantum dash lasers using dual optical feedback with improved tolerance against phase delay mismatch.

We experimentally investigate the RF linewidth and timing jitter over a wide range of delay tuning in a self-mode-locked two-section quantum dash lasers emitting at ~ 1.55µm and operating at ~ 21 GHz repetition rate subject to single and dual optical feedback into gain section. Various feedback conditions are investigated and optimum levels determined for narrowest linewidth and reduced timing jitter for both single and dual loop configurations. We demonstrate that dual loop feedback, with the shorter feedback cavity tuned to be fully resonant, followed by fine tuning of the phase of the longer feedback cavity, gives stable narrow RF spectra across the widest delay range, unlike single loop feedback. In addition, for dual loop configurations, under fully resonant conditions, integrated timing jitter is reduced from 3.9 ps to 295 fs [10 kHz-100 MHz], the RF linewidth narrows from 100 kHz to < 1 kHz, with more than 30 dB fundamental side-mode suppression. We show that dual loop optical feedback with separate fine tuning of both external cavities is far superior to single loop feedback, with increased system tolerance against phase delay mismatch, making it a robust and cost-effective technique for developing practical, reliable and low-noise mode-locked lasers, optoelectronic oscillators and pulsed photonic circuits.